Rsr Fuel Pressure Gauge View From 1bar Ölgefüllt Benzindruckmesser

  
Rsr fuel pressure gauge display 1 bar ölgefüllt benzindruckmesser. This product page has been automatically translated. If you have questions, feel free to contact us. Gauge: Stainless steel / polished adapter material: brass manometer ø: 40 / 47mm / glycerine filled gauge display: 0-1 bar gauge thread: 1/8 npt thread of the adapter 3 x 1/8 npt diameter cable: 7,5 - 9,5 mm in total length of the adapter: 80 mm (40 mm tube fitting) with hex adapter t: 40 mm wide / angle 30 mm gauge size key: 12 mm connector key size: 11 mm key width tee: 15 mm weight: 240g. In other auctions, the adapter and the gauge are also available individually, eg.

For retrofitting on gas regulators with displays without glycerine filling! The vehicle operating list is only a sample list !! a universal fuel pressure gauge 0-1 bar with connection adapter for fuel lines (rubber material) with an inner diameter of ø 7.5 to 9.5 mm, most fuel conduits have an inner diameter ø 7.5 to 8.0 mm, for example. For injected engines vw / audi / seat / Skoda / Opel.

The installation must take place in the pressure line to the fuel pressure regulator! To do this, the line (rubber fabric) is disconnected and the pressure gauge inserted therebetween. The adapter is compact and fits almost anywhere in between.

The total length is 80 mm, the hose connection is 40 mm long (2 x 20 mm). The gauge, the adapter and the sealing strip are provided individually so they can be installed straight or angle, as required. Tee has threads 3 1/8 npt, which means that the pressure gauge can be screwed into any position. The pressure gauge and screw connections must be approx. 5 times right before the screw. The display varies from 0 to 1 bar and the pressure gauge to glycerin is filled, which means that the value can be read exactly when the engine is running. The pressure gauge is necessary for troubleshooting in the fuel supply zone, which may be defective or too small petrol pumps, regulators or clogged filters.

For small pumps, the gas pressure drop with increasing engine speed, this is usually a problem with powerful engines, the pressure should maintain its value until the limiter, if this is not the case, the engine may become poor, resulting in overheating and engine damage! In the sub power / accessory shop you will find the black and white gauge with a range of 1 bar-o, o-4 bar or 0-7bar or standard version in white 0-11bar. Installation note: Tighten the pressure gauge with only a 12 mm wrench, do not shake hand or turning the gauge, it can damage the gauge !!

the installation should only be performed by qualified personnel! The manometer description data manometer techniques: stainless steel / polished adapter material: brass manometer ø: 40 / 47mm / glycerine filled gauge display: 0-1 bar gauge thread: 1/8 NPT adapter: 3 x 1/8 npt cable diameter: 7,5 - 9,5 mm in total length of the adapter: 80 mm (40 mm tube fitting) with hex adapter t: 40 mm wide / angle 30 mm gauge key size: 12 mm connector key size: 11 mm width key tee: 15 mm weight: 240g the use of vehicles list is just a sample list !!!

Installation note: installation should be performed by the person. The seller is \This article can be shipped worldwide.

1. product type pressure gauge <\/ li>
2. adapter wire: 3 x 1 / 8NPT <\/ li>
3. gauge wire 1 / 8NPT <\/ li>
4. produkt abroad: yes <\/ li>
5. manometer diameter: 40mm / 47mm (anello) <\/ li>
6. inner cable diameter: 7,5-9,5mm <\/ li>
7. Article modified: yes <\/ li>
8. Custom: 0-1bar <\/ li>
9. Manufacturer: performance rsr <\/ li>
10. manufacturer part number: kma - set1 <\/ li>
11. brand - no brand / generic - <\/ li> <\/ Ul>